ALPINA Front Splitter Spoiler Logo Graphic Sticker Letter black silver grey gold

EUR 7,20 Achat immédiat 18h 44m, EUR 1,11 Livraison, 30-Day Retours, Garantie client eBay

Vendeur: useful-bits-and-bobs (7.573) 100%, Lieu où se trouve: Chepstow, Lieu de livraison: Worldwide, Numéro de l'objet: 302906325877 If you are considering purchasing this item, please read the listing IN FULL beforehand as there is a lot of detail contained herein. Thanks. ALPINA front splitter vinyl logo in a choice of colours, in both standard 300mm (12") and 360mm (14,2") widths. These fit onto the raised lettering on the front splitter of the car to highlight the manufacturer designation. These may be supplied with either clear, or paper release tape, but the installation method is the same for both types of release tape. Colours available:- Silver Matt Silver Gloss (almost chrome) Graphite Grey (360mm available as either high gloss or metallic finish) Gold (360mm available as either gloss or matt finish) Black Gloss To be 100% clear: You are purchasing 1 logo, not a set of 4 colours or 4 logo's. Please specify the size (300mm or 360mm) and colour(s) (Gold (matt or gloss), Silver (matt or gloss), Graphite Grey (gloss or metallic) or Black) you require at purchase via a message. They are direct copies of the original letter kits, and printed on Image Perfect High Performance IP5700 vinyl (Gold currently on Graphitack Vinyl). The vinyl is as good as, if not better than, the factory supplied material and is ideal should you be needing to refresh an existing graphic kit. The letters have to each be added individually, ie cut from the letter strings supplied, and stuck onto the raised lettering 1 by 1 as the spacing of the printing does not match the spacing of the lettering on the car (this is normal and occurs even with the factory supplied kits). ALPINA used 2 sizes of graphic, nominally 300mm and 360mm. The 300mm graphic fits the E60/61 pre-LCI B5, E85 Roadster S, E90/91 D3 (single turbo pre-LCI), E90/E91 B3Biturbo and many others. The 360mm graphic fits the E60/61 LCI B5, E90/91/92/93 D3Biturbo,B3SBiturbo, E92/E93 B3Biturbo, F01 B7 Biturbo, F10/11 D5 Biturbo and B5 Biturbo, F30/31 B3 Biturbo and D3 Biturbo, B4 and D4 and again, various others. If you are unsure, to determine which one fits your car, measure the widest point of your lip spoiler lettering at the bottom (ie A to A). If your measurement is 300-310mm, the 300mm is the graphic for your car, if the measurement is 355-370mm, then the 360mm graphic is for you. Please indicate with a message on your purchase which size and colour you require. Alternatively, send me a message via the message centre, ie 'contact seller'. That will then ensure you the fastest despatch of your logo as I cannot despatch without this vital information. Thankyou. In the images above:- image 1 shows the colour options (top to bottom: graphite grey metallic, matt gold , matt silver, gloss silver, black) graphic (logo) with a clear release tape so the logo can be clearly seen image2 shows the graphic (logo) with a paper release tape for any supplied as such. image3 shows the 2 sizes commonly used for demonstration only (you will receive only 1 graphic (logo) unless you multibuy) image 4 shows the graphics fitted to my car for illustration only (car not included with graphic (logo)). For reference, the colour of this graphic is Graphite Grey metallic on a black car. If in any doubt about your ability to fit these successfully, I'd suggest you buy 2 sets to cover any possibility of damaging the lettering during fitting! A guideline for the installation is included at the bottom of this listing. Please note carefully the following:- Due to damage in the post caused by postmen folding large items for small/tight letterboxes and hence causing creasing of the logo, I now will only supply the kits cut into 2 smaller sections (halves) to keep them small and harder to damage in transit. This has no effect whatsoever on the item and its fitting. I will not supply these uncut as the risk of damage outweighs the benefit, so please do not ask!! Any purchase made with a request to supply in one piece will be cancelled under ebay's policy of buyer requesting a service not offered, and you will be refunded in full. I will contact you and give you a chance to withdraw the 'uncut' request before I do cancel the purchase, but if we cannot agree, you will be refunded and the purchase cancelled. If you are then using these on a model which is NOT an ALPINA, join the 2 pieces together with sellotape on the release paper side (only one clean cut is used to separate them) and you can apply to the vehicle in one single piece. Any questions, just ask. Itemswill generally be posted the same day for orders completed by midday; the following morning for orders completed after this. Items purchased after 10am on Saturday will be posted Monday morning. I obtain a minimum of a certificate of postage for all items: a scanned copy can be supplied for any order on request. Please note:- Your satisfaction in using my service is paramount to me. Rest assured I post most items same day, or the following working day where an item is purchased outside PO opening/collection hours. If you are in any way dissatisfied with any aspect of my service or product, please contact me and we can work to resolve your concerns. Installation instructions:- Remove any old graphics with care (they can be difficult) Chemicallyclean the raised lettering with something like isopropyl alcohol (methscan be used but may leave a residue, or VERY CAREFULLY a quick wipe with nail varnish remover....no rubbing with this). Don't touch the cleaned paint with your fingers, now. Cut the letters into their individual squares:You can cut close to the letters if you wish, but you need to allow material to handle the letters a little as if you touch the adhesive side of them, they won't stick properly. Fit the 'I' 1st - easiest and a good practise starting point. Remove the paper backing (the paper with the squares on it) Line it up with the spoiler letter and start to apply it from one corner. If you are unhappy with the alignment peel it back off (note 'peel' not pull/tug) and try again Fully press the letter down and, if all good, apply thumb force all over. Remove release paper by peeling from one corner Gently rub all over with a soft cloth, starting from the centre and working to the vulnerable corners. Next fit the 'L' following previous method Then fit the 'P' following previous method taking care to get the open hole of the letter in perfect position. Then tackle the 'A's and the 'N' in whichever order you fancy. They are equally awkward and patience is required. Don't power wash the area for a week. Condition: New, Theme: Logo, Type: Graphic, Unit Type: Unit, Placement on Vehicle: Front, Brand: Alpina

autisticsocialskills.com Insights autisticsocialskills.com Exclusif
  •  Popularité - 382 vues, 4.2 views per day, 90 days on eBay. Super grande quantité sur vues. 17 vendu, 465 disponibles.
  •  Prix -
  •  Vendeur - 7.573+ articles vendu. 0% évaluations négative. Grand vendeur avec la très bonne rétroaction positive et plus de 50 cotes.
Articles similaires Items
Sitemap